The Optimization of Spheroidizing Heat Treatment Parameters on SCM440 Alloy Steel Wires Using Taguchi Robust Design
DOI:
https://doi.org/10.14738/aivp.106.13301Abstract
In the fastener industry, SCM440 alloy steel wire is widely used in the production of cold forging parts, such as high-strength steel fasteners, auto parts, hardware supplies, etc. The wire manufacturers use an intercritical process for spheroidized annealing the alloy steel wires. The quality of a spheroidized annealed wire affects the cold forging quality of fasteners. A series of experimental tests on SCM440 alloy steel wires is carried out in a commercial hydrogen furnace. Various parameters such as spheroidized annealing temperature (A), prolonged heating time (E), holding temperature and time (B, C), cooling rate and temperature (D, F) affect the quality characteristics of wires, such as tensile strength, hardness and ductility. The effects of intercritical spheroidized annealing treatment on mechanical properties are investigated using Taguchi robust design to obtain optimal spheroidized annealing conditions to improve the mechanical properties of alloy steel wires for cold forming. It is experimentally revealed that the spheroidized annealing temperature (A), cooling rate and temperature (D, F) significantly affect the quality of spheroidizing annealed SCM440 alloy steel wires. The optimal spheroidized annealing conditions for SCM440 alloy steel wire are spheroidized annealing temperature of 771°C and prolonged heating for 5.0 h, then holding the temperature of 725°C for 1.0 h, and slowly cooling to the temperature of 713°C at the rate of -9°C /h. Therefore, the optimal mean tensile strength of 520.0 MPa, optimal mean hardness of 80.8 HRB, and optimal mean ductility of 0.488 are obtained. The variations of the properties are significantly reduced to achieve a much even quality for annealed wires. The optimal spheroidizing heat treatment parameter settings evidently improve the performance measures and the cold formability of SCM440 alloy steel wires is effectively improved.
References
. Dhers, J.; Thivard, B.; Genta, A., Improvement of steel wire for cold heading. Wire Journal International, 1992, 25(10): p. 73-76.
. Bramfitt, B.L. and Hingwe, A.K., Annealing of steel. In Heat Treating, ASM International: Materials Park, OH, USA, 1991.
. Johnson, P., Furnace Atmospheres. In Heat Treating, ASM International: Materials Park, OH, USA, 1991.
. Hernández-Silva, D.; Morales, R.D.; Cabañas-Moreno, J.G., The Spheroidization of Cementite in a Medium Carbon Steel by Means of Subcritical and Intercritical Annealing. ISIJ International, 1992. 32(12): p. 1297-1305.
. O’Brien, J.M. and Hosford, W.F., Spheroidization Cycles for Medium Carbon Steels. Metallurgical and Materials Transactions A, 2002, 33(4): p. 1255-1261.
. Gul’, Y.P.; Sobolenko, M.A.; Ivchenko, A.V., Improvement in the Spheroidizing Annealing of Low-Carbon Steel for Cold Upsetting. Steel in Translation, 2012. 42(6): p. 531-535.
. Raji, N.A. and Oluwole, O.O., Effect of Soaking Time on the Mechanical Properties of Annealed Cold-Drawn Low Carbon Steel. Materials Sciences and Applications, 2012. 3(08): p. 513-518.
. Ikpeseni, S.C.; Onyekpe, B.O.; Ovri, H., Influence of Intercritical Annealing Temperature on Mechanical Properties and Microstructure of 0.23%C Low Alloy Steel. Nigerian Journal of Technology, 2015. 34(3): p. 499-505.
. Qian, D.S.; Wang, K.W.; Liu, Q.L.; Hua, L., Effect of Annealing Parameters on Microstructure and Mechanical Property of Hot-rolled 100Cr6 Bearing Ring. Materials Science and Technology, 2016. 32(11): p. 1086-1093.
. Yang, C.-C. and Wang, S.-T., Improvement of the Mechanical Properties of Spheroidized 10B21 Steel Coil Using Taguchi Method of Robust Design. Sensors and Materials, 2018. 30(3): p. 503-514.
. Ji, C.; Wang, L.; Zhu, M.-Y., Effect of Subcritical Annealing Temperature on Microstructure and Mechanical Properties of SCM435 Steel. Journal of Iron and Steel Research, International, 2015. 22(11): p. 1031-1036.
. Ayres, J.; Penney, D.; Evans, P.; Underhill, R., Effect of Intercritical Annealing on the Mechanical Properties of Dual-phase Steel. Ironmaking & Steelmaking, 2022. 49(8): p. 821-827.
. Yang, C.-C. and Lu, N.-H., The Inspection of Spheroidized Annealing on SCM435 Cold-Forging Quality Steel Wires with Protective Atmosphere. Materials Sciences and Applications, 2019. 10(11): p. 677-686.
. Equbal, M.I.; Equbal, A.; Equbal, M.A.; Pranav, R., Optimisation of Forging Parameters of 35C8 Steel Using Grey Relational Analysis. International Journal of Microstructure and Materials Properties, 2018. 13(3/4): p. 198-212.
. Nasiri, Z. and Mirzadeh, H., Spheroidization Heat Treatment and Intercritical Annealing of Low Carbon Steel. Journal of Mining and Metallurgy, Section B: Metallurgy, 2019. 55(3): p. 405-411.
. Yang, C.-C. and Lu, N.-H., Improvement in Performance of Cold-drawn SCM435 Alloy Steel Wires through Optimization of Intercritical Annealing Parameters. Sensors and Materials, 2019. 31(11): p. 3639–3654.
. Soleimani, M.; Mirzadeh, H.; Dehghanian, C., Effects of spheroidization heat treatment and intercritical annealing on mechanical properties and corrosion resistance of medium carbon dual phase steel. Materials Chemistry and Physics, 2021. 257.
. Radnia, A.; Ghaini, F.M.; Miresmaeili, R., Intercritical and subcritical spheroidization of 10B38 cold heading steel. Materials Research Express, 2019. 6(9).
. Spindola, M.O. and Buono, V.T.L., Effect of intercritical annealing with high cooling rate associated with cold deformation and subcritical annealing on microstructure and mechanical properties of SAE 52100. Journal of Materials Research and Technology, 2020. 9(4): p. 9136-9141.
. Scheuermann, W.; Böing, D.; Wittler, P.; Bock, M.A.; Bovalina, T., New developments in hydrogen annealing of steel coils. MPT Metallurgical Plant and Technology, 1995. 18(2): p. 90-96.
. Messina, C.J., Raw Material Processing: Advances in Spheroidize Annealing of Wire Rod Using 100% Hydrogen. Fastener Technology International, 2011. February: p. 26-27.
. Saboonchi, A. and Hassanpour, S., Experimental and Numerical Investigation of Coil Heating in Hydrogen Annealing Furnace for Optimum Arrangement of Charge. Experimental Heat Transfer, 2008. 21(3): p. 220-235.
. Logothetis, N., Managing for Total Quality: From Deming to Taguchi and SPC. 1992, London: Prentice Hall International (United Kingdom).
. Lee, H.-H., Taguchi Methods: Principles and Practices of Quality Design. 2008, New Taipei City: Gau Lih Book (Taiwan).
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Chih-Cheng Yang, Yu-Ning Lu, Chen-Lun Sung
This work is licensed under a Creative Commons Attribution 4.0 International License.
